Used scaffolding is the fastest way to grow a fleet. Bought well, it does the same job as new material, sooner and for less. Bought badly, you are left with a pile that cannot be completed and cannot be erected together.
The difference usually shows up not while negotiating the price, but while working out what the material actually is.
Where used scaffolding comes from
Second-hand material has three sources, and they are not the same thing:
- Returning rental fleet. Usually the tidiest: many components of one system, a known manufacturer, and often a parts list.
- Material sold at the end of a project. A system a contractor bought for its own work and released when the job finished. Quantities are good, but because it stayed on one site, the wear may be concentrated in one place.
- Liquidation and mixed lots. The cheapest and the riskiest. Components of different systems end up in the same stack.
That is why the first question is not the price: which system is this?
When it makes sense
- You already own the same system and are adding in the same dimensions.
- The programme is tight: it ships from existing stock instead of waiting for a production slot.
- The work sits in a low load class — painting, rendering, insulation.
- The quantity is large and comes as one lot, from one system.
When it does not
- The lot is mixed brands. The wedge of one system may fit the rosette of another; that does not mean they were calculated together. Mixed systems are not erected.
- The manufacturer is unknown. If the system cannot be identified, neither can its load class.
- Spares will not be available. The day a wedge head or a platform hook cannot be found, the whole system waits.
- The material is going under formwork. Loads there are an order higher; never put material with an unknown history into a shoring system.
What to check on the ground
A short list — never close a deal without seeing the material:
- Standards: bends and dents; deformation in rosettes and flanges.
- Welds: cracks, especially around the rosettes.
- Surface: where the galvanising has worn through and rust has started; on painted material, what is under the lifted paint.
- Platforms: permanent deflection, hooks opening up, worn anti-slip surface.
- Wedge heads: spreading from being hammered; missing wedges.
- Jacks: damaged threads and bent spindles.
- Parts list and erection manual: without them the lot is not a system.
We run the same checks when buying new — item by item in what to check when buying scaffolding.
How the paperwork works
This is the most misread part. The system certification (TS EN 12810 / TS EN 12811 conformity) belongs to the product type and its manufacturer; the type does not change hands when the material does. But two things become your responsibility:
- Being able to prove which system it is. If the manufacturer and type cannot be identified, the load class cannot be established either. We explained what the classes mean in scaffold load classes.
- Assessing the condition of used material. A certificate does not treat it as new; deformed components are set aside before erection.
What moves the price
The discount on used material is not one percentage; it is the sum of four things:
- Surface: galvanised or painted, and how many seasons it spent outdoors.
- Homogeneity: one system or mixed. A mixed lot always looks cheaper and always has a smaller usable share.
- Completeness: if wedges, hooks and jacks are missing, you complete them out of your own pocket.
- Quantity and haulage: material collected from scattered locations eats the discount in logistics.
A rough rule: price it on the usable share. Not "this much per tonne", but "this much for the square metres that can actually be erected".
Where we stand
REMA both sells and rents used scaffolding. The difference is this: we still manufacture the same systems in the same dimensions. When a component is missing or deformed, the system does not have to be replaced — it is completed from production. The spare-parts problem that hits used material hardest does not arise.
What is available depends on stock; send the dimensions and the square metres you need and we will compare them against what we hold.
In short
- Ask "which system is this?" before "how much?".
- A mixed-brand lot is not erected; its cheapness is only apparent.
- A system still in production is the biggest advantage used material can have.
- Never put material with an unknown history under formwork.
- Price it on erectable square metres, not on tonnage.
Send us your list, or the square metres you need, and we will work out whether used or new comes out cheaper for the job.